Adam's EVIL R32

[Adamolee]

Hey folks,

All work has been completed by Ramspeed, Thomas and Andrew spent many months with me going over the details, swapping ideas, listening to my nonsense, getting me back on track, offering suggestions and toying with ideas. I cannot speak highly enough of the time and consideration invested in each step, infinite thanks must go to Jack for bringing it all together.

Completed

ABT Supercharger – Stage 1
Audi TT Injectors
550NM Clutch pack
Strengthened clutch cage
Custom DSG software (Spec below)
Modified transfer case - Race spec, secret squirrel fluids and dust seals
Capristo - (Always open)
ADV 7 – 3 Piece Forged deep concave 18 x 9 Matte Satin Black
H&R sway bars – Front & Rear
Vogtland Coilovers – Height & Damper adjust
Solid engine mounts – Lower, Side & Gearbox
Nolathane bushings – Control arm, Trailing arm & steering rack
Blacked out VW badges – Front & Rear
OSIR Carbon Valence
Haldex GEN 2 Blue Controller & Switch (Always in "race")
Blue LED interior lights
Fake RNS 510
11 Inch Focal sub & Amp – Custom moulding
Custom illuminated gadget stash in armrest
UNIBRACE Underbody
UNIBRACE Stressbrace
OEM Smoked LED Tails – US Spec, Fog delete
LED Plate lights
Black knurled A/C bezels
Blue R36 Coil pack covers
Blue Coilpack covers and tubing
Carstyle4U Switches - Eject + Tacks
Piano black DSG shift surround
Golf MKVI Steering rack
Whiteline Anti-lift Kit

Planning

Headers
High flow cats
Injectors
Modified supercharger pulley
Custom ECU tune
BBK
Headlight trim respray

DSG Tune

Pos - DSG adjustment - Mode

1 torque limit increase to 550Nm

2 Increase of automatic up shifting - NO - Manual

3 Deactivation of automatic up shifting - Manual
Note: Rev Limit will be reached

4 Deactivation of Kick down - Manual

5 Increase Launch Control - 4250 RPM - LC

6 Shift time - Shortest possible 50ms (Up to) - D, S and M

7 Increase of max rev limit +1000 RPM

8 Increase of max revs at down shifting

9 Adjustment of shift points D and S

10 Adjustment of start up regulators - D, S and M
For reinforced clutches

11 Adjustment of start up torque - D, S and M

12 Adjustment of gear change timing - D, S and M

A few preview pics

http://img824.imageshack.us/img824/1425/sam0976.jpg By adamole (http://profile.imageshack.us/user/adamole)

http://img831.imageshack.us/img831/9220/sam0987i.jpg By adamole (http://profile.imageshack.us/user/adamole)

http://img15.imageshack.us/img15/4838/sam0981i.jpg By adamole (http://profile.imageshack.us/user/adamole)

http://img535.imageshack.us/img535/6411/sam1001l.jpg By adamole (http://profile.imageshack.us/user/adamole)


The ABT Power R Supercharger kit

http://ramspeed.com.au/forum/attachment.php?attachmentid=709&d=1293597414
http://ramspeed.com.au/forum/attachment.php?attachmentid=710&d=1293597496

Clutch cage, DSG & Mechatronic - MY DSG was replaced by VW 6 weeks prior to starting the build, Hence shiney :)

http://ramspeed.com.au/forum/attachment.php?attachmentid=713&d=1293597549
http://ramspeed.com.au/forum/attachment.php?attachmentid=715&d=1293597588
http://ramspeed.com.au/forum/attachment.php?attachmentid=718&d=1293597637

Cage and Mechatronic ready for shipping

http://ramspeed.com.au/forum/attachment.php?attachmentid=728&d=1293685671
http://ramspeed.com.au/forum/attachment.php?attachmentid=729&d=1293685687

Prep work before the power increase - Injector & port clean

http://ramspeed.com.au/forum/attachment.php?attachmentid=719&d=1293597653 - Before
http://ramspeed.com.au/forum/attachment.php?attachmentid=722&d=1293597703 - After
http://ramspeed.com.au/forum/attachment.php?attachmentid=725&d=1293685562 - Before
http://ramspeed.com.au/forum/attachment.php?attachmentid=726&d=1293685627 - After

Pre boost'age tasks - Water pump, intercooler, intake and buzz-kill material

http://ramspeed.com.au/forum/attachment.php?attachmentid=735&d=1294373497
http://ramspeed.com.au/forum/attachment.php?attachmentid=736&d=1294373520
http://ramspeed.com.au/forum/attachment.php?attachmentid=1111&d=1302069671
http://ramspeed.com.au/forum/attachment.php?attachmentid=1113&d=1302069681

Suspension, Bushings & Mounts

http://ramspeed.com.au/forum/attachment.php?attachmentid=1114&d=1302069684
http://ramspeed.com.au/forum/attachment.php?attachmentid=733&d=1294373433
http://ramspeed.com.au/forum/attachment.php?attachmentid=734&d=1294373455
http://ramspeed.com.au/forum/attachment.php?attachmentid=1117&d=1302069694
http://ramspeed.com.au/forum/attachment.php?attachmentid=723&d=1293597717 - Stock part
http://ramspeed.com.au/forum/attachment.php?attachmentid=1116&d=1302069691 - Solid part

Secret Squirrel Box - Hides Capristo, Haldex & BASS

http://ramspeed.com.au/forum/attachment.php?attachmentid=1127&d=1302072467

3rd Supercharged MKV R32 on the road

http://ramspeed.com.au/forum/attachment.php?attachmentid=2381&d=1315461069
http://ramspeed.com.au/forum/attachment.php?attachmentid=2384&d=1315461116


More pics here -Linky (http://www.vwgolf.net.au/showthread.php?5825-Adam-s-EVIL-R32&p=126742&viewfull=1#post126742)

And more pics here - Linky (http://www.vwgolf.net.au/showthread.php?5825-Adam-s-EVIL-R32&p=126163&viewfull=1#post126163)

And even more pics here - Linky (http://www.vwgolf.net.au/showthread.php?5825-Adam-s-EVIL-R32&p=173275&viewfull=1#post173275)


Next?

Mid engine VW Scirocco AWD Twin supercharged Audi V8 7 Speed Getrag DCT

[CSR]

Good start..Will reserve my comments for when the PIX come :)




Mid engine VW Scirocco AWD Twin supercharged Audi V8 7 Speed Getrag DCT

WTF?

Bombshell right there. I don't even know if that's serious or can be done but it sounds absolutely gorgeous. Though if you said twin turbo charged would've been even more jaw dropping.
Some "custom" ideas right there...What is a door handle delete + remote pop? You mean like, lambo doors or something?

[Adamolee]

Hey CSR

Not scissor doors, just no door handles and solenoid actuated opening from a remote fob ...

That is way down the line, Got to catch up with Jig first ..

:D

[GBJ-R32]

ahhh shitttt!!

Boss!

[Rob32R]

Very nice mod's Adam :). Can't wait to see this in the flesh and some pictures of your beast, how much hp has this rocket got.

[just_quietly]

"Mid engine VW Scirocco AWD Twin supercharged Audi V8 7 Speed Getrag DCT"

Holy crap. Power to weight will be crazy. Lucky for the boot because thats where you'll find your nuts most of the time!

[Adamolee]

ahhh shitttt!!

Boss!

:D


Very nice mod's Adam :). Can't wait to see this in the flesh and some pictures of your beast, how much hp has this rocket got.

Cheers Rob,

Probably around 400Hp / 400Nm, Hence the need to overdrive the supercharger, ABT design the kit to be OEM not extreme. it complies to some very strict and fancy sounding acronyms, so now i've got one it's time to void the warranty!

Jose is already on that path, if you take a peek at his thread he has completed, the work needed to take the next step, with pulleys, headers, cats, next step is the tune ...

[mikinoz]

Things have come a long way in modding R32's in Australia since the MKIV days I can see.

Out of interest, after dropping so much coin - why the fake RNS510? Just seemed a bit odd.

+1 for pics :)

[CSR]

:D



Cheers Rob,

Probably around 400Hp / 400Nm, Hence the need to overdrive the supercharger, ABT design the kit to be OEM not extreme. it complies to some very strict and fancy sounding acronyms, so now i've got one it's time to void the warranty!

Jose is already on that path, if you take a peek at his thread he has completed, the work needed to take the next step, with pulleys, headers, cats, next step is the tune ...

Sorry, 400Nm ?? Surely not?


Things have come a long way in modding R32's in Australia since the MKIV days I can see.

Out of interest, after dropping so much coin - why the fake RNS510? Just seemed a bit odd.

+1 for pics :)

Haha I noticed that as well :D random thing to have a "fake" of.

Btw I loved your central armrest gadget cubby, very very creative, I like the way you view your mods.

[Adamolee]

Things have come a long way in modding R32's in Australia since the MKIV days I can see.

Out of interest, after dropping so much coin - why the fake RNS510? Just seemed a bit odd.

+1 for pics :)

I have plenty of crap phone pics but i'll hold out for some slick ones, just waiting to hook up a shoot then i'll get them up ..

re: the RNS, impatience.

[Adamolee]

Sorry, 400Nm ?? Surely not?



Haha I noticed that as well :D random thing to have a "fake" of.

Btw I loved your central armrest gadget cubby, very very creative, I like the way you view your mods.

Just what ABT quotes at the crank, no idea if the dyno will back it up or not, Jig can probably add some wisdom here

http://i978.photobucket.com/albums/ae266/jig69r/ABT%20Sportsline%20Supercharger%20Kit%20Install/ABTSC-DataSheet.jpg

[melbv]

definitely sub'd
please load photos soon... cant wait!!

[stephen8512]

Finally made a build thread on your beast Adam!

Adam was kind enough to give me a shotgun ride in this thing and it's just so nice...Capristo in the background, supercharger whine at the front, instant pull...and thats just me being the passenger. Can only imagine how fun this would be when driving and cruising around. Prob one of the few people I have met who has a keen eye and attention to detail, even on the small things! Big things matter but its the little things and personal touches that makes the car "yours"

Love your work mate :) Catch up soon!

[sxcR32]

WOWWWWW!!!
loving this already!

Eagerly waiting for pics now haha

[10d]

Looking forward to the pics!

[MasterKevin]

Yeh in for the nice pics!

[Nathan_b]

Awesome spec sheet, welcome to VWGolf :)

[Stalker]

Amazing! ...wanna swap? :D

[SUGA]

Great to see this build thread up here! Photos soon please :)

[Jig]

Its started... The pictures will do justice to this car I am 100% positive. Crazy build thread list Adam. Impressive.

[Adamolee]

Its started... The pictures will do justice to this car I am 100% positive. Crazy build thread list Adam. Impressive.

It's all your fault!

:D

[*thad*]

in for pics!

[Adamolee]

First pics,

not giving much away, best I can do with a toy camera ....

DHL seem to want to keep my LED tails, but will sort more once they are fitted along with the UNIBRACE gear and flared guards ...

[just_quietly]

F A T

[MiLos]

subbed, great work mate, loving that 1st pic!

[Jig]

Just what ABT quotes at the crank, no idea if the dyno will back it up or not, Jig can probably add some wisdom here

http://i978.photobucket.com/albums/ae266/jig69r/ABT%20Sportsline%20Supercharger%20Kit%20Install/ABTSC-DataSheet.jpg

That's for sure Adam. The ABT folks needed to comply with TUV and the easiest way to do that is keep the modification to OEM standards. The SC manufacturer actually says the SC in the ABT unit has so much more potential. The acceleration speed is spot on an OEM R32. Put lightweight wheels & BBK and catback exhaust, some great suspension mods and you will find the acceleration around 4.8s dead... My MKV R32 did 4.8s to a 100k fully loaded. I dont put too much emphasis on acceleration anyway but that is the number right now...

[CSR]

That's for sure Adam. The ABT folks needed to comply with TUV and the easiest way to do that is keep the modification to OEM standards. The SC manufacturer actually says the SC in the ABT unit has so much more potential. The acceleration speed is spot on an OEM R32. Put lightweight wheels & BBK and catback exhaust, some great suspension mods and you will find the acceleration around 4.8s dead... My MKV R32 did 4.8s to a 100k fully loaded. I dont put too much emphasis on acceleration anyway but that is the number right now...

Hi Jig,

When you say "so much more potential", do they have any quoted figures? What is it currently boosting to, what is it capable of? For stage 2, are you opening up the engine or keeping stock internals?

[Adamolee]

Jig may have more inside info on this, he always whip's out some facts when you need em ...

As far as i am aware however there are no figures available, as there are only 3 kits in Aus, all of which are stage 1 (out of the box) it's not been done here, i beleive for Jig he will be leaving internals alone, however as he has extractors and high flow cats fitted he can overdrive the compressor, couple that with fatter injectors (possibly different fuel pumps too) and a custom tune and there you have stage 2. my understanding is ABT will either not warrant or not perform the tune, so to pull all this together we need some additional input from Kubatech. Jose is on the verge of making this happen so i am very keen to get all the details. he has updated his build thread with the steps taken so far

as for stage 3, who knows...

it is possible to push the R32 engine past 600Hp on stock internals, obviously cooling, lubricants, rods & bolts are all factors. but if you consider what AP has done with his you can see the potential of the engine.

[just_quietly]

Supercharged turbo? :eek:

[Adamolee]

Supercharged turbo? :eek:

:D

No just a lot of boost on stock internals ...

[zz2]

crikey Adam! you're certainly modding properly

[M4RK0]

Awesome!! can wait to see in the flesh!!!

How far you are planning to go with this car Adam?, until it flies!!!!

Good Mod's!

[schoona]

Jig may have more inside info on this, he always whip's out some facts when you need em ...

As far as i am aware however there are no figures available, as there are only 3 kits in Aus, all of which are stage 1 (out of the box) it's not been done here, i beleive for Jig he will be leaving internals alone, however as he has extractors and high flow cats fitted he can overdrive the compressor, couple that with fatter injectors (possibly different fuel pumps too) and a custom tune and there you have stage 2. my understanding is ABT will either not warrant or not perform the tune, so to pull all this together we need some additional input from Kubatech. Jose is on the verge of making this happen so i am very keen to get all the details. he has updated his build thread with the steps taken so far

as for stage 3, who knows...

it is possible to push the R32 engine past 600Hp on stock internals, obviously cooling, lubricants, rods & bolts are all factors. but if you consider what AP has done with his you can see the potential of the engine.

Even though the R32 is special (especially in Aus) regarding FI, normal FI rules would still apply. More, dense, cooler air and good velocity with the right amount of fuel.

ABT boost pressure is only 6psi with the S/C? There would definitely be potential left in the setup for higher boost pressure. (Is the charger a Vortech unit branded ABT or??)
More cfm + more fuel (big squirters (stay off redtube Clem!))

As always, it's in the tune and these ABT cars seem to be getting great service from Ramspeed + partners regarding their cars so the software will surely get sorted.

I didn't notice a head spacer to decompress in the parts list, perhaps that (from VF or similar) is an option to drive the charger even harder. Add some bigger valves + Schrick camshafts or similar and has to be more in this combination before losing too much of the "OEM" in chase of "spastic".

Not from personal experience but looking at R32OC/vortex etc, even the little 2.8 12V can push 400whp (proper wheel not hub dyno crap) with a head spacer and a GT35R. Plenty of R32s with similar turbos and bigger on standard internals, though Jose would forge it for "Peace of Mind" anyway, which isn't a bad thing after all.

GL in the chase Adam, nice 32 :)

[Adamolee]

Inspiration for my next build


650Hp twin Supercharged R32 (http://www.stormdevelopments.co.uk/twin-rotrex-r32.html)

[Adamolee]

definitely sub'd
please load photos soon... cant wait!!

Pics should be appearing now


Finally made a build thread on your beast Adam!

Adam was kind enough to give me a shotgun ride in this thing and it's just so nice...Capristo in the background, supercharger whine at the front, instant pull...and thats just me being the passenger. Can only imagine how fun this would be when driving and cruising around. Prob one of the few people I have met who has a keen eye and attention to detail, even on the small things! Big things matter but its the little things and personal touches that makes the car "yours"

Love your work mate :) Catch up soon!

Thanks for the kind words, ready when you are mate


Awesome spec sheet, welcome to VWGolf :)

Why thank you


Amazing! ...wanna swap? :D

How fit's your missus?


Great to see this build thread up here! Photos soon please :)

Thanks SUGA, been keeping it under wraps till now


Its started... The pictures will do justice to this car I am 100% positive. Crazy build thread list Adam. Impressive.

Following in the footsteps of greater man than I, Jose ;D

[Adamolee]

F A T

Semi, still a while to go before we reach full PHAT


subbed, great work mate, loving that 1st pic!

Thanks mate, $60 dick smith special + a little fiddling


crikey Adam! you're certainly modding properly

Doing the best I can, Need more time and acces to a money tree


Awesome!! can wait to see in the flesh!!!

How far you are planning to go with this car Adam?, until it flies!!!!

Good Mod's!

I have a picture in my mind and i'm about half way there, health keeps getting in the way so it has to take a back seat for a few months at a time.

It may never end, which will certainly make for interesting reading

[CSR]

Jig may have more inside info on this, he always whip's out some facts when you need em ...

As far as i am aware however there are no figures available, as there are only 3 kits in Aus, all of which are stage 1 (out of the box) it's not been done here, i beleive for Jig he will be leaving internals alone, however as he has extractors and high flow cats fitted he can overdrive the compressor, couple that with fatter injectors (possibly different fuel pumps too) and a custom tune and there you have stage 2. my understanding is ABT will either not warrant or not perform the tune, so to pull all this together we need some additional input from Kubatech. Jose is on the verge of making this happen so i am very keen to get all the details. he has updated his build thread with the steps taken so far

as for stage 3, who knows...

it is possible to push the R32 engine past 600Hp on stock internals, obviously cooling, lubricants, rods & bolts are all factors. but if you consider what AP has done with his you can see the potential of the engine.

AP's R32 engine is single turbo, not sure what HP it puts out but as per the dyno day it is running 216 KW at all wheels in his Golf Wagon. Let's say 30% drivetrain loss through the AWD system as has been quoted many times before as an average. That's about 410 HP at the crank if i'm not mistaken.

HPA suggest replacing Conrods at 450 HP on VWVortex:

Conrods should be linked to HP..or if you track the car. 450+..get the bearings,…autocross/road course, ¼ race..get the bearings!

I also doubt highly his R36 TT engine is running on stock internals.
You seem like a careful guy, if you replaced clutchpacks for 400 Nm of torque then you should be looking at strengthening the engine internals before increasing boost :)

[Jig]

Jig may have more inside info on this, he always whip's out some facts when you need em ...

As far as i am aware however there are no figures available, as there are only 3 kits in Aus, all of which are stage 1 (out of the box) it's not been done here, i beleive for Jig he will be leaving internals alone, however as he has extractors and high flow cats fitted he can overdrive the compressor, couple that with fatter injectors (possibly different fuel pumps too) and a custom tune and there you have stage 2. my understanding is ABT will either not warrant or not perform the tune, so to pull all this together we need some additional input from Kubatech. Jose is on the verge of making this happen so i am very keen to get all the details. he has updated his build thread with the steps taken so far

as for stage 3, who knows...

it is possible to push the R32 engine past 600Hp on stock internals, obviously cooling, lubricants, rods & bolts are all factors. but if you consider what AP has done with his you can see the potential of the engine.

You know what I know Adam. Cant wait to get our cars sorted with Stage 2. Your right, keeping pistons and rods stock for now as I really dont plan to hit 500HP+ on this car. Heck, I even have stock DSG plates and OEM DSG software tune, unlike your HGP ones. I think you are better poised for Stage 2 than I am(LOL).

The ABT SC kit already has a second high pressure fuel pump installed. So it can take more boost. It needs bigger fuel injectors however to make Stage 2. You have to remember that superchargers are different to turbo chargers as far as induction is concerned. SC power is via pulley/belt where turbos via exhaust.

SC also generates less heat. Less heat, more cold air stuffed into that VR6 engine. In fact, not sure if you have noticed, but during summer, my SC R32's performance is not hindered at all by our summer heat/humidity but my 911 for example, suffers badly. Same with my Viggen back in the day.

[Jig]

Even though the R32 is special (especially in Aus) regarding FI, normal FI rules would still apply. More, dense, cooler air and good velocity with the right amount of fuel.

ABT boost pressure is only 6psi with the S/C? There would definitely be potential left in the setup for higher boost pressure. (Is the charger a Vortech unit branded ABT or??)
More cfm + more fuel (big squirters (stay off redtube Clem!))

As always, it's in the tune and these ABT cars seem to be getting great service from Ramspeed + partners regarding their cars so the software will surely get sorted.

I didn't notice a head spacer to decompress in the parts list, perhaps that (from VF or similar) is an option to drive the charger even harder. Add some bigger valves + Schrick camshafts or similar and has to be more in this combination before losing too much of the "OEM" in chase of "spastic".

Not from personal experience but looking at R32OC/vortex etc, even the little 2.8 12V can push 400whp (proper wheel not hub dyno crap) with a head spacer and a GT35R. Plenty of R32s with similar turbos and bigger on standard internals, though Jose would forge it for "Peace of Mind" anyway, which isn't a bad thing after all.

GL in the chase Adam, nice 32 :)

Spot on Mal. Longevity and reliability is where it is at although Adam is the crazier of the two. His build is sounding angry and its great to see this level of modifying in our country. Big kudos'. The ABT SC is from Switzerland. I forget the brand. Need to get a torch and have a look under the bonnet.

[Adamolee]

Regarding Clemente and jose's posts above,

HGP's state that they change the bearings at 500Nm and the shells at 630Nm, There is no talk of rods, bolts or caps etc ... that is not to say it is not a wise idea.

as Jose has just said he will be leaving his for now, as for me this will definately happen.

My engine has done many more miles and a lot on the track, so a bulltproof bottom end is on the cards but not till i'm ready to increase boost.

discussion like this is a testament to the wisdom contained within the community, great stuff guys

[Adamolee]

Mal i definately need to pick your brains re: internals / engine rebuild!

[schoona]

AP's R32 engine is single turbo, not sure what HP it puts out but as per the dyno day it is running 216 KW at all wheels in his Golf Wagon. Let's say 30% drivetrain loss through the AWD system as has been quoted many times before as an average. That's about 410 HP at the crank if i'm not mistaken.

HPA suggest replacing Conrods at 450 HP on VWVortex:


I also doubt highly his R36 TT engine is running on stock internals.
You seem like a careful guy, if you replaced clutchpacks for 400 Nm of torque then you should be looking at strengthening the engine internals before increasing boost :)

I know it's me saying with it but forget the owner, a decent sized turbo + the 3.2 + the mods I'd be hoping for a lot more than what he got. Hopefully he gets the numbers he deserves with a few more tweaks. Johns Golf R made 210 with basic bolt on mods, so there is more left in his beast of a wagon surely.

[schoona]

Mal i definately need to pick your brains re: internals / engine rebuild!

I'm just the internet, don't believe eveyrthing you read.

The largest thing to consider is what Ramspeed will be comfortable doing and backing up when things go wrong because I can't support your expensive habit :P

I'm glad Jose went with C2 with his Mk4, hope its a pleasant experience, but the C2/United Motorsport cars seem to be a bit more aggressive (it's the point of doing all this right?) and getting the big numbers O/S. The annoying part about it is nothing in Aus compares to O/S at all.

[Jig]

Inspiration for my next build


650Hp twin Supercharged R32 (http://www.stormdevelopments.co.uk/twin-rotrex-r32.html)

That is crazy setup Adam. Let me be one of the firsts to sit next to you when this hapens please. I like the bi-supercharger setup as well, more so than twin superchargers. Same applies to bi-turbos. Smaller chargers for lower rpms to give it a quick burst then when the smaller setup runs out of puff, the bigger charger keeps pulling all the way to the red line. Very, very nice indeed. Do it!

[CSR]

I know it's me saying with it but forget the owner, a decent sized turbo + the 3.2 + the mods I'd be hoping for a lot more than what he got. Hopefully he gets the numbers he deserves with a few more tweaks. Johns Golf R made 210 with basic bolt on mods, so there is more left in his beast of a wagon surely.

Oh for sure there is more in it. He dyno'ed it the next day and got 236 kw ATW, I Just went by the last 'known' record on the forums so as to be correct.

I think before it got put in his wagon it was doing 280 KW atw.

[maca]

No one's asked the question;


Does it dose?



But seriously, this is insane. A little awkward when you walk out and see four strangers admiring and taking photos of your car :P

[Adamolee]

No one's asked the question;


Does it dose?



But seriously, this is insane. A little awkward when you walk out and see four strangers admiring and taking photos of your car :P

A little , but still nice to meet the crew and to be honest it was the first time anyone had ever stopped for a chat to admire the car,

re: Doseing, no. The charger is connected directly to the crankshaft unlike a turbo so it does what the rev counter does, very addictive when in sport mode and the throttle blips on downshifts ...

[Adamolee]

That is crazy setup Adam. Let me be one of the firsts to sit next to you when this hapens please. I like the bi-supercharger setup as well, more so than twin superchargers. Same applies to bi-turbos. Smaller chargers for lower rpms to give it a quick burst then when the smaller setup runs out of puff, the bigger charger keeps pulling all the way to the red line. Very, very nice indeed. Do it!

We are in danger of getting way ahead of ourselves here and i am hijacking my own thread but its either that engine build in a 4WD Rocco or one of these Linky (http://www.undergroundracing.com/vehicles/audi-r8-v10)

There is another company who builds a Twin charged R8 with magnetically coupled superchargers ...

How's your money tree looking :D

[Adamolee]

Mod 1 / Stage 4 perhaps ... ?


The standard Golf has never had such a powerful engine as the new R32. Its 3.2-litre V6 engine is a gem of German Engineering. The power output of the R32's transverse six-cylinder engine is 240 BHP (at 6250 rpm) capable of 0.60mph in just 6.6 seconds.

The R32's four-valve six-cylinder engine is distinguished by its very acute 15-degree V angle. Two overhead camshafts with continuous intake and exhaust camshaft adjustment are used in the cylinder head. The adjustment angles are 52 degrees for the intake camshaft and 22 degrees for the exhaust camshaft. The valves are driven by roller rocker fingers with hydraulic clearance compensation. Each cylinder has its own ignition coil.

From a technical point of view, the 3.2-litre V6 engine, with its crankshaft with seven main bearings, is of a similar concept to the 2.8-litre engine, which powers the Golf, Bora and Sharan V6. However, it has been improved in so many different aspects that it really ought to be regarded as a new generation of that engine.

Our gas flow measurements show that it has very good inlet flow but there was a lot of room for improvement on the exhaust side. After a challenging and extensive period on the flow bench we were able to raise the Inlet flow by 6% to 161.6 CFM. On the exhaust side we were able to make a huge increase of 30% to 129CF. This level of flow means this engine is capable of over 400BHP in normally aspirated form. (Turbo applications are popular on this head and we would expect over 800 bhp if this head were used with a turbo modification.)

[schoona]

That the CNC heads Adam? (forget the company name, in the UK though I think?)

[Adamolee]

That the CNC heads Adam? (forget the company name, in the UK though I think?)

What can i say mate, you inspired me

http://www.cncheads.co.uk/vw_r32.html

:D

[schoona]

:)

Pleasure. lol

[CSR]

What can i say mate, you inspired me

http://www.cncheads.co.uk/vw_r32.html

:D

Is that 1,250 pounds including the exchange or without exchange? Seems expensive for a bit of porting to the OEM head if that's what I'm understanding from that link..?

Edit - Just read the FAQ, 1,250 pounds is including you giving your head to them. Expensive little job..

[zbeasty]

Give these guys a call. Highly recommended. http://www.ramsheadservice.com.au/

[Adamolee]

Is that 1,250 pounds including the exchange or without exchange? Seems expensive for a bit of porting to the OEM head if that's what I'm understanding from that link..?

Edit - Just read the FAQ, 1,250 pounds is including you giving your head to them. Expensive little job..

Wrong continet too :P

[Adamolee]

Give these guys a call. Highly recommended. http://www.ramsheadservice.com.au/

Nice find mate,

Just found another company who supply forged rods, bulletproof bottom ends etc ... NGP Racing (http://www.ngpracing.com/store/index.php?dispatch=categories.view&category_id=71)

keep it coming folks

[richie32]

spotted yesterday in brighton, looking very tough, loving this thread

[sxcR32]

Man I wanna this!!!!

[Adamolee]

spotted yesterday in brighton, looking very tough, loving this thread

Hey buddy, that was you I spotted,

mate your car is slick, looks like it just rolled off the factory floor, very tidy mate

:D

[Adamolee]

A few nice bits & pieces are on the way ...

Order receipt from P3 Cars Company LLC
ECS Tuning-Your Order has Shipped
CarStyle4you - Order confirmation
BKS Tuning - Order receipt confirmation

If anyone needs me, I'll be camping by the post box for the next week

[Frenchie]

Quite an intense weapon you packing AJ!!

[CSR]

A few nice bits & pieces are on the way ...

Order receipt from P3 Cars Company LLC
ECS Tuning-Your Order has Shipped
CarStyle4you - Order confirmation
BKS Tuning - Order receipt confirmation

If anyone needs me, I'll be camping by the post box for the next week

:D Nice!

Let me see..
P3 Gauge
ECS - F*cked if I know
CarStyle4you - Garage Door button
BKS Tuning ?

[Adamolee]

:D Nice!

Let me see..
P3 Gauge - Bingo
ECS - F*cked if I know - LED's, Coil pack's, Bezel's
CarStyle4you - Garage Door button - In the guise of an ejector seat :D
BKS Tuning ? - OEM Smoked LED tail lights - US Spec (No fog light)

Also have UNIBRACE Underbody and rear stress brace ready to install, Guards are being flared next Wednesday and clay bar + polish friday arvo ...

Waiting on Kics Dual phase lugs to arrive too

[Adamolee]

Quite an intense weapon you packing AJ!!

To quote a dear friend "Is it built to outrun Satan or something?"

[10d]

Waiting on Kics Dual phase lugs to arrive too

Mate, just checking that your ADV have the tapered/conical seat yeah? If not those KICS won't suit the wheels if you have the ball seat type.

[BBR32]

OEM Smoked LED tail lights - US Spec (No fog light)
this will look so so so good ..what ones on the site are they ..? link

[Adamolee]

Mate, just checking that your ADV have the tapered/conical seat yeah? If not those KICS won't suit the wheels if you have the ball seat type.

Ball seat :(

No harm, they are not paid for just pick up.

so what options do i have for tatsy lug bolts,

and thanks for spotting that, you are The Oracle!

[Adamolee]

OEM Smoked LED tail lights - US Spec (No fog light)
this will look so so so good ..what ones on the site are they ..? link

Linky (http://www.bks-tuning.com/epages/17141421.sf/en_GB/?ObjectPath=/Shops/17141421/Products/VWGOL052/SubProducts/VWGOL052-LHD)

Yum!

[BBR32]

oh very nice hmm might be someing to look at for mine ....pics when done please :)

[BBR32]

why did you go for the US Version) ?

[10d]

Ball seat :(

No harm, they are not paid for just pick up.

so what options do i have for tatsy lug bolts,

and thanks for spotting that, you are The Oracle!

Lol. Not the Oracle. That's Jig.

You want fancy ones, go with the RAYS Formula Bolts. They make them in various sizes and length.

http://tapatalk.com/mu/79d1e46f-2ba8-b32c.jpg

[VOLK5]

nice work mate! would love to see moarr photos of the wheels!

I wanted a set of KICS dual phase nuts, however the above worked out just as well, especially in black!

[Adamolee]

why did you go for the US Version) ?

The LHD or RHD version have 1 fog and 1 reverse, The US spec has no fog light,

symetry my good man, it gives me tingles

:D

[Adamolee]

Lol. Not the Oracle. That's Jig.

You want fancy ones, go with the RAYS Formula Bolts. They make them in various sizes and length.

http://tapatalk.com/mu/79d1e46f-2ba8-b32c.jpg


Thanks 10d, i really appreciate you catching that one and for the suggestion.

How about "The Don" instead?

;)

[Adamolee]

nice work mate! would love to see moarr photos of the wheels!

I wanted a set of KICS dual phase nuts, however the above worked out just as well, especially in black!

We have a photo shoot hooked up for the 25th. should have LED's, Unibrace, flared guards, tasty lug's all in by them ...

Will hook up some sexy wheel action too

[Rob32R]

Sounds good Adam :).

Who's doing the photoshooting?

Are you fitting Kerscher Widened Guards like AP?

[Adamolee]

Sounds good Adam :).

Who's doing the photoshooting?

Are you fitting Kerscher Widened Guards like AP?

The frenchman has offered to take some pics, we each have a few locations in mind so looking forward to getting some nice pics up, none of mine do the car justice.

Not going with the widened guards, just rolling teh lip and flaring the outer edge of the guard a few degrees, should look pretty tough when it's done

[stephen8512]

cant wait for the pics AJ

[CSR]

For someone into symmetry you have two very unsymmetrical badges on the back of your hatch and one on the right of your front grille..

DEBADGE TIME!! ;)

[Fab_R]

Great stuff Adam...cant wait for more pics dude ;)

[Pharkus]

Linky (http://www.bks-tuning.com/epages/17141421.sf/en_GB/?ObjectPath=/Shops/17141421/Products/VWGOL052/SubProducts/VWGOL052-LHD)

Yum!

+1 to these, may have to replace mine =(

They look good.

[Adamolee]

For someone into symmetry you have two very unsymmetrical badges on the back of your hatch and one on the right of your front grille..

DEBADGE TIME!! ;)

But how will I know i'm cool?

[Adamolee]

+1 to these, may have to replace mine =(

They look good.

I love the LED tails on the R32, no idea why it was not factory spec,

been waiting for 3 weeks but DHL tell me they are out for delivery today - pics will follow


Great stuff Adam...cant wait for more pics dude ;)

I'll try take a few Fisher Price pics but Frenchie and I are hooking up some proper shots on the 25th


cant wait for the pics AJ

Any day now mate

[Adamolee]

Different finishes available in OEM LED tails for MKV

Lots more styles here - BKS Tuning (http://www.bks-tuning.com/epages/17141421.sf/en_GB/?ObjectPath=/Shops/17141421/Categories/Volkswagen/Golf/%22Golf%20V%22/Lightning/Rueckleuchten)

Standard

http://img202.imageshack.us/img202/2382/standardf.jpg


Clear

http://img14.imageshack.us/img14/8844/clearcj.jpg

Smoked

http://img535.imageshack.us/img535/8956/smoked.jpg

[Pharkus]

I liked the smoked ones. Do you know the difference between the LHD and RHD models? Are they just different in that the fog lens has already been swapped to the correct side?

I would prefer the US Spec ones as you say for symmetry, let us know how you go with the installs. I may have to order some as well *sigh.

[Adamolee]

I liked the smoked ones. Do you know the difference between the LHD and RHD models? Are they just different in that the fog lens has already been swapped to the correct side?

I would prefer the US Spec ones as you say for symmetry, let us know how you go with the installs. I may have to order some as well *sigh.

Spot on RE: fog light on the correct side,

Dont sigh just yet, wait till you order a set and DHL take 3 weeks to ship em to you, Than you can sigh

:D

[M4RK0]

Standard Adam!

[Pharkus]

Spot on RE: fog light on the correct side,

Dont sigh just yet, wait till you order a set and DHL take 3 weeks to ship em to you, Than you can sigh

:D

I think I have been quite patient (read as unmotivated) with my inners. 1 year on still not installed and in pieces and I also have a full set of normal MKV tails as well which I was going to scavenge the lens from but still haven't. CANNOT WAIT for pics as mine is also UG so will get direct look of them off you!

[BBR32]

have you got them yet :) :)

[Adamolee]

have you got them yet :) :)

They just arrived, very well packed

although i cant go and put them in because the car is in the body shop getting a paint treatment ...

itchy fingers man ....

[BBR32]

pics :)

[Pharkus]

itchy fingers man ....

What sort of paint treatment?

Confucius would suggest you keep those fingers away from your butt hole.

[Adamolee]

pics :)

I present to you the LED's of infinite pleasure and awesomeness

Nice 8 page instruction booklet included and a pack of Haribo - Result!

:D



http://img9.imageshack.us/img9/8027/sam1004.jpg

http://img705.imageshack.us/img705/9608/sam1005d.jpg

http://img706.imageshack.us/img706/8294/sam1007e.jpg

http://img163.imageshack.us/img163/4571/sam1006o.jpg

[Adamolee]

What sort of paint treatment?

Confucius would suggest you keep those fingers away from your AMAZING butt hole.

Getting all the swirl marks removed, de-wax, wash, polish + glaze, when the guy said glaze i first thought of donut's and then porn

so i shall forever refer to it is my porno donut car wash

[BBR32]

oooooooooo they look good AJ

[chris32]

Can't wait too see these installed.

Sent from my GT-I9100T using Tapatalk

[CSR]

Getting all the swirl marks removed, de-wax, wash, polish + glaze, when the guy said glaze i first thought of donut's and then porn

so i shall forever refer to it is my porno donut car wash

Or donut porno car wash!

[Adamolee]

Or donut porno car wash!

Both conjure unsightly imagery, yet equally amusing :D

[CSR]

Is your car black or UG?

Everyone is saying UG but the pictures in your first post are all of a black R32...Or am I colourblind? ??

[Rob32R]

Its black Clem, it can't be UG because it is a darker colour than grey. Your definately not colour blind :lol:. Read the specs of his car on this page http://ramspeed.com.au/forum/showthread.php?452-VW-Golf-R32-MKV-ABT-SportsLine-Supercharger-Kit

[CSR]

Thanks for the confirmation..Guess everyone is thinking Adam is JayC or something as they keep mentioning UG R32 ...

[BBR32]

https://www.dectane.de/RUeCKLEUCHTEN/Rueckleuchten-VW/LITEC-LED-Rueckleuchten-VW-Golf-V-03-09--red-smoke.html?XTCsid=9d57d35c48d29c880f3ae0d5ad147dc5

DOO IT haha

[CSR]

Shit I was going to stay away from headlight changes but...that looks pretty cool...Any pictures of it on an r32?

[Pharkus]

One question. If the lights are brand new, why would they have swirlies on them already. I would get mine Opti-coated and corrected in any case just cos the rest of my car has had the same treatment.

[BBR32]

One question. If the lights are brand new, why would they have swirlies on them already. I would get mine Opti-coated and corrected in any case just cos the rest of my car has had the same treatment.

i think he means the R32 not the lights

[BBR32]

Shit I was going to stay away from headlight changes but...that looks pretty cool...Any pictures of it on an r32?

not R32 but gti mk5 and ohhhh yeah haha http://www.youtube.com/watch?v=sg7HInzMtro&feature=related

[Adamolee]

Thanks for the confirmation..Guess everyone is thinking Adam is JayC or something as they keep mentioning UG R32 ...

Yeh I have been mistaken for Jayc a few times, car is black mate, everything in my garage is ...

P.s change your pic, i wanna do things to it!

[Adamolee]

One question. If the lights are brand new, why would they have swirlies on them already. I would get mine Opti-coated and corrected in any case just cos the rest of my car has had the same treatment.

If i'm reading you right mate, it is just a trick of the light, they are proper slick but with the flash up that close it creates some nasty special effects,

Bright lights, curved surfaces etc ...

Just re-read this ...

The swirls i was talking about are in my paint, i thuoght you asked about the swirls in the pics i took of the LED's .. hence explination above and Blake being a total genius

See, dipstick, can't take me anywhere ....

[Adamolee]

P.S just to keep things interesting, Car was picked up from the body shop today and taken to ramspeed with 3 boxes of gear in the back,

with any luck it will be back on the road by Saturday or i'll be turning up to zee German autofest in a Merc!

Hardly represent'n VWGOLF in that beast!

And a little blue card in the letter box tells me there is another box of goodies waiting for me at the P.O.

And I just saw Jig's MKIV Brakes folks, That is some angry hardware!

And i've run out of milk!

[stephen8512]

P.S just to keep things interesting, Car was picked up from the body shop today and taken to ramspeed with 3 boxes of gear in the back,

with any luck it will be back on the road by Saturday or i'll be turning up to zee German autofest in a Merc!

Hardly represent'n VWGOLF in that beast!

And a little blue card in the letter box tells me there is another box of goodies waiting for me at the P.O.

And I just saw Jig's MKIV Brakes folks, That is some angry hardware!

And i've run out of milk!

some delicious mods coming from both you and Jose.... getting a funny feeling in my pants AJ ;)

[CSR]

not R32 but gti mk5 and ohhhh yeah haha http://www.youtube.com/watch?v=sg7HInzMtro&feature=related
That looks hot!!!!


Yeh I have been mistaken for Jayc a few times, car is black mate, everything in my garage is ...

P.s change your pic, i wanna do things to it!

ME TOO! I keep finding myself opening that picture up every 2 mins so figured it'd be better to just leave it here ;)

[GBJ-R32]

oh snap to the picture man that face that you want to destroy.

pics adam we need pics

[Adamolee]

some delicious mods coming from both you and Jose.... getting a funny feeling in my pants AJ ;)

Yeh thats Jig's doin not mine, he does it to me too

:D

[Adamolee]

oh snap to the picture man that face that you want to destroy.

pics adam we need pics

Pics, sure, anytime ... Now getting back to your previous sentence, what like Destroy, destroy or D E S T R O Y, destroy

Slightly off topic i know but Clem started it,

Sexy clem, who i'll now go and thnk about while i "try" to fall asleep ...

[Adamolee]

That looks hot!!!!



ME TOO! I keep finding myself opening that picture up every 2 mins so figured it'd be better to just leave it here ;)


So ahhh


about that picture,

would it be possible to ahhh

somehow


Acquire the rest of .....


uhhhh

[CSR]

hahaha i feel bad for making your thread go offtopic!!

She is Olivia Wilde..Tbh I wouldn't even want a nude picture of her, her eyes do it all for me!!!! I'm a sucker for sexy eyes.

[Rob32R]

She is amazing Clem :p. Adam i'm enjoying your build thread progress :)

[Adamolee]

hahaha i feel bad for making your thread go offtopic!!

She is Olivia Wilde..Tbh I wouldn't even want a nude picture of her, her eyes do it all for me!!!! I'm a sucker for sexy eyes.

adam googles olivia Wilde .......... J A C K P O T!

Worry not my good man, with all the spannerin takin place on my ride we'll be back on track in no time, now i must be off, i have 'research' to attend

[Adamolee]

She is amazing Clem :p. Adam i'm enjoying your build thread progress :)


It's the ladies not the car right,

:D

[VOLK5]

<----- I need R32 tail lights!!! :(

[OraQube]

Those smoked led tails are mighty tempting!!

I definitely prefer them over the standard lenses.

[BBR32]

where are the pics with them on the car ????

[Adamolee]

where are the pics with them on the car ????

Hey buddy,


only just picked up the car then,

will pop down and take some shots now, but be warned , they are going to be fisher price, my first digi-cam shots

[GBJ-R32]

Finaly some pics, can't wait to see this

[BBR32]

ohhhhh yeah going to be good ....im ready and waiting for this pro pics hahaha

[Adamolee]

Here are my Anti-professional pics, sorry about the dodge quality

Car will be in ACT tommorow so hopefully someone who knows how to use a camera will capture some better shots,


p.s. Check out my moon boots!



http://img23.imageshack.us/img23/4713/sam1014w.jpg

http://img641.imageshack.us/img641/5426/sam1013i.jpg

[CSR]

HOT! And sexy moonboots.

Are your tips meant to be black or haven't had a wash in a while? :P

[BBR32]

ohhh man that really looks good .well done love it

[Adamolee]

HOT! And sexy moonboots.

Are your tips meant to be black or haven't had a wash in a while? :P

Just for you (because you're sexy)

http://img844.imageshack.us/img844/5890/sam1016z.jpg

http://img845.imageshack.us/img845/1639/sam1015z.jpg

[Adamolee]

ohhh man that really looks good .well done love it

Thanks mate, i really appreciate that, it is a very hard thing to capture with a kids camera ...

[Ashcombe]

Superb car. Excellent color and its nice that it is fully loaded. I hope you take good care of your car.

[CSR]

Just for you (because you're sexy)

http://img844.imageshack.us/img844/5890/sam1016z.jpg

http://img845.imageshack.us/img845/1639/sam1015z.jpg

HAHA NICE!! You didn't just do that did you? Fark that's a lot of soot.

Also is your rear valance OSIR?

[Adamolee]

HAHA NICE!! You didn't just do that did you? Fark that's a lot of soot.

Also is your rear valance OSIR?


I did it after i took the pics of the lights about 4 hrs ago, put yes, i walked down 6 flights of stairs just for you(r face)

Yep it's an OSIR badger, very tidy

:D

[GBJ-R32]

Fark that's so nice man. Congratz.
Also well done with the cleaning

[sxcR32]

I was actually gonna ask about the exhaust too haha

Looks better now :)

Brilliant car!!! Looks HOTTTTT

[BBR32]

Thanks mate, i really appreciate that, it is a very hard thing to capture with a kids camera ...

no prob i really want them now i keep looking at them haha im like you not good at all with pics lol

[Pharkus]

Is it my monitor colour calibration, your picture or a combination but does the smoke effect on the tails look a bit brown?

[GBJ-R32]

yea they do look brown, had to go back to check it out

[schoona]

Looks good Adam :)

[VOLK5]

Here are my Anti-professional pics, sorry about the dodge quality

Car will be in ACT tommorow so hopefully someone who knows how to use a camera will capture some better shots,


p.s. Check out my moon boots!



http://img23.imageshack.us/img23/4713/sam1014w.jpg

http://img641.imageshack.us/img641/5426/sam1013i.jpg

nice! cant wait to get my badges back from the spray painters!

[Jig]

The picture does not show it justice. It does not look brown at all in real life. Must see, love the tails Adam.

[Justin Fox]

http://farm7.static.flickr.com/6166/6158055434_a7ebbdef35_o.jpg
Congrats on the trophy bud!!!!!!! :)

[Type 17]

The annoying part about it is nothing in Aus compares to O/S at all.


Not Yet ;)

OP, Whats the deal with your charger, where is the pully hanging off? (seems like it is on the wrong side)

Do MK5's have a completely different setup to that off the MK4?

Edit* read back and see that you have your charger running of your crank. Intersting.

It is a great little setup very nice MK5 I dont know about this stg 1/2/3 crap, you are at stage you if you ask me.

Definitley run a solid bottom end, cams, injectors and lower the compression when you want to unleash the kracken!

Me Im doing custom stuff but also running a water/air intecooler, i would recommend running a larger heat exchanger if and when you do light up the boost gauge.

[Adamolee]

http://farm7.static.flickr.com/6166/6158055434_a7ebbdef35_o.jpg
Congrats on the trophy bud!!!!!!! :)

Thanks Justin,

totally unexpected win by the noob there

[Adamolee]

Getting back to the LED tail's,

right now i'm not sure how I feel about the finished product,

They are very hard to capture unless you are looking at them for real, but i have noticed a slight haze in the lens which is due to the smoked effect, it is only noticable when you put your face up to them but it is there.

there are other products on the market that will achieve the same result such as Lamin-X which can be applied to any light, LED, OEM or otherwise, so if anyone is considering fitting smoked LED's of any type, i would urge you to compare the two, happy to let you see what i am talking about, just PM me.

depending on the amount and direction of light, they will have a different colour and i can see why people see them as brown, but as Jig mentioned, in flesh this is not the case, a blacked out car is always going to be tricky to shoot

[VOLK5]

sad to hear mate - let me know if you ever think about selling up?

[Adamolee]

Not Yet ;)

OP, Whats the deal with your charger, where is the pully hanging off? (seems like it is on the wrong side)

Do MK5's have a completely different setup to that off the MK4?

Edit* read back and see that you have your charger running of your crank. Intersting.

It is a great little setup very nice MK5 I dont know about this stg 1/2/3 crap, you are at stage you if you ask me.

Definitley run a solid bottom end, cams, injectors and lower the compression when you want to unleash the kracken!

Me Im doing custom stuff but also running a water/air intecooler, i would recommend running a larger heat exchanger if and when you do light up the boost gauge.

Full internal rebuild is on the cards however i am focussed on BBK next, then the new front end, a handful of monor aesthetic tweaks and blemishes require attention, however i have already started to gather info and suppliers for the components needed to rebuild the block and heads..

re: the charger placement, the ABT compressor sits in the middle of the engine bay and is mounted to the DSG, drive for the compressor does run off the crank pulley which is located on the other side of the engine however drive os fed to it from a forged shaft which runs under the intake runners, which is why it looks to be placed in an unusual location. this allows plenty of room for the compressor, charge cooler and CAI

Looking forward to seeing your mods take shape, especially when you use the word "custom"

Great to catch up with you mate, nice arse too ;)

[Adamolee]

sad to hear mate - let me know if you ever think about selling up?

G'day mate,

it's not a showstopper, but whenever you buy a product that has not been tested or seen you run a risk,

don't get me wrong though, the effect is still very pleasing, and the look really does fit what i was hoping to achieve for the car. it is a minor detail which i was not expecting and again, is only evident at a particular angle from close up.

many didnt notice until i pointed it out,

did i mention i am a chronic perfectionist ?

[Pharkus]

I just wasn't sure whether it was my monitor, the photo or the effect of the light available. Always have to ask to make sure!

Gratz on the award though, well deserved.

[Adamolee]

Some new pre show pics

http://img585.imageshack.us/img585/4/dsc1683p.jpg

http://img856.imageshack.us/img856/6531/dsc1684f.jpg

http://img594.imageshack.us/img594/598/dsc1685g.jpg

http://img594.imageshack.us/img594/4052/dsc1682.jpg

http://img843.imageshack.us/img843/3682/dsc1681q.jpg

http://img41.imageshack.us/img41/9439/dsc1678l.jpg

http://img263.imageshack.us/img263/1309/dsc1676g.jpg

http://img197.imageshack.us/img197/4577/dsc1675p.jpg

[Adamolee]

I just wasn't sure whether it was my monitor, the photo or the effect of the light available. Always have to ask to make sure!

Gratz on the award though, well deserved.

Way to calibrate your monitor :D

Thanks Pharkus, definately a great way to cap off my first event

[Rob32R]

Adam... This R32 is beautiful. I'm tempted to modify mine seriously :). Congratulations on the trophy well deserved. Don't let a tinge of brown smoked L.E.D tails upset you.

[Adamolee]

Adam... This R32 is beautiful. I'm tempted to modify mine seriously :). Congratulations on the trophy well deserved. Don't let a tinge of brown smoked L.E.D tails upset you.

Cheers budd,

i'm going to start referring it to my "crappiest" mod if people dont stop using the word brown

i sat in the garage for 10 mins last night just locking and unlocking the car, wathcing the LED show

grinning from ear to ear

[73landau]

Great buildup. You could paint the discs to give a total black out from the side view >D ..... Just pulling your leg. I first saw your car on the ramspeed site.
It is looking absolutely brilliant. I hope I can achieve just 10% of your effort in order to have a great car. I like the LED taillights even with the colourisation of the camera chip :cool:
I like the Mk6 style LEDs also posted in this thread (I was following one to work last week)

Waiting for your next mods and posts.

Cheers Greg

[BBR32]

can anywhere do the smoked tails to the OEM ones i know you used to be able to get it done but dont know now ..hmmm im thinking of just doing that ..but i still love this AJ LED all the way lol

[VOLK5]

Some new pre show pics

http://img585.imageshack.us/img585/4/dsc1683p.jpg

http://img856.imageshack.us/img856/6531/dsc1684f.jpg

http://img594.imageshack.us/img594/598/dsc1685g.jpg

http://img594.imageshack.us/img594/4052/dsc1682.jpg

http://img843.imageshack.us/img843/3682/dsc1681q.jpg

http://img41.imageshack.us/img41/9439/dsc1678l.jpg

http://img263.imageshack.us/img263/1309/dsc1676g.jpg

http://img197.imageshack.us/img197/4577/dsc1675p.jpg

looks great mate, reminds me of mine, minus all the goodies you've got going on?

what are your wheels & tyre specs? and is your rear badge a custom/gloss black? I've had mine sprayed the same as the colour of the car, not sure how its going to look!

[Adamolee]

Great buildup. You could paint the discs to give a total black out from the side view >D ..... Just pulling your leg. I first saw your car on the ramspeed site.
It is looking absolutely brilliant. I hope I can achieve just 10% of your effort in order to have a great car. I like the LED taillights even with the colourisation of the camera chip :cool:
I like the Mk6 style LEDs also posted in this thread (I was following one to work last week)

Waiting for your next mods and posts.

Cheers Greg

Thanks Greg,

Brakes will be ordered shortly but i'm sticking with my blue theme, however i am doing my best to specify the finish and colour of the hat, i know it's bananas but is important to me, discs will be slotted and callipers will be OEM blue with .:R logo - before i had the car detailed they did actually look black!

thanks for the kind words, much appreciated,

can anywhere do the smoked tails to the OEM ones i know you used to be able to get it done but dont know now ..hmmm im thinking of just doing that ..but i still love this AJ LED all the way lol

Hey buddy, if you dont wish to buy smoked lighst there is a product called Lamin-X which comes in various colour finishes, one of which is tinted, Stephen used to have it on his Accord and it looked slick, do some googling and you will find out more, definately a good value way to get the effect on any style of light,

[Adamolee]

looks great mate, reminds me of mine, minus all the goodies you've got going on?

what are your wheels & tyre specs? and is your rear badge a custom/gloss black? I've had mine sprayed the same as the colour of the car, not sure how its going to look!

You crack me up mate,

wheels are ADV - 7 - 3 piece forged concave finished in satin black, 18 x 8.5, with an offset of 45, 225 dunlop sport max all round, this gives a slightly strecthed effect and exagerats the concave of the wheel nicely, they are extremely light, i have a 2nd set of centre caps which i am getting CNC'd but have not had time to finalise the design so hopefully this will bring a new element to the car as what i am hoping to achieve has never been done, even the guys at ADV where shocked when i suggested it


rear badge is is the factory unit, resprayed by Ramspeed who now have a pertnership with a fantastic body shop, they will be doing some work for me shortly to repair, roll and flare my guards and some more custom paintwork, all very subtle and of course, BLACK!

I think if you take it one step at a time you will get the right balance, i only made 1 change at a time to the rear of the car so i was able to get a feel for what each step would look like, wait until your badges are fitted, then consider lights, once they are fitted, see what comes next. i think you will be very pleased when you see your coded badges,

[Adamolee]

For anyone interested in darkened lights here is an alternative product called Lamin-X

they can be fitted at home or by a tint shop or detailer such as Reflect Effect..

they will fit over most OEM lights

http://www.vwgolf.net.au/showthread.php?1143-Lamin-X-Protective-Films

http://www.lamin-x.com/VW-Golf-GTI-Rabbit-2005-to-2009-s/747.htm

[Adamolee]

Hey Kids,


Apologies for the delay in updating this bad boy,

In the last 2 weeks I have completed the following,

Unibrace XB - Fitted
Unibrace UB - Fitted
CarStyle4You Eject + Tacks - Fitted ( Garage door mod pending)
DSG shift surround painted - Piano black
Small dent in driver door repaired - PDR
Full detail - de-wax, wash, buff & glaze
P3 Guage has cleared customs and should be delivered during the week - 0 to 100 time to follow
Replaced steering rack with MKVI unit, mine was making ugly sounds VW suggested the swap, will report back after a week or 2 when i can work out if this constitutes a repair or possible mod, definately has a different feel, but hard to tell when mine was knackered.

Stay tuned

:D

[stephen8512]

Hey Kids,


Apologies for the delay in updating this bad boy,

In the last 2 weeks I have completed the following,

Unibrace XB - Fitted
Unibrace UB - Fitted
CarStyle4You Eject + Tacks - Fitted ( Garage door mod pending)
DSG shift surround painted - Piano black
Small dent in driver door repaired - PDR
Full detail - de-wax, wash, buff & glaze
P3 Guage has cleared customs and should be delivered during the week - 0 to 100 time to follow
Replaced steering rack with MKVI unit, mine was making ugly sounds VW suggested the swap, will report back after a week or 2 when i can work out if this constitutes a repair or possible mod, definately has a different feel, but hard to tell when mine was knackered.

Stay tuned

:D

Love it AJ! Cant wait for the 0-100 times mate. Rear lights completes the murdered out theme!

Would love to see this beast once again. Hope u will be coming to the DIY meet

Any plans for BBK;s later on down the track mate?

[Adamolee]

Love it AJ! Cant wait for the 0-100 times mate. Rear lights completes the murdered out theme!

Would love to see this beast once again. Hope u will be coming to the DIY meet

Any plans for BBK;s later on down the track mate?


Morning chief,

BBK is still in planning phase, it will happen, without giving it all away some of the things we are duscussing

hat colour & finish, weight (reduce unsprung), slot design (not using drilled), calliper manufacturer and so on

Brakes for me are as much an aesthetic component of the car as well as performance, the car does not live on a track so i should be able to improve on both areas.

with regards to the acceleration times i'm as interested as you, will be nice to see how consistent the car is and also measure any difference in D, S & LC mode.

i'm sure there is a thread here that has people P3 or 0 to 100 times in it but i can only find track time thread, have you any idea where it might be?

I'll be at the DIY mate so we can catch up there, or you could move to Manly

[stephen8512]

Morning chief,

BBK is still in planning phase, it will happen, without giving it all away some of the things we are duscussing

hat colour & finish, weight (reduce unsprung), slot design (not using drilled), calliper manufacturer and so on

Brakes for me are as much an aesthetic component of the car as well as performance, the car does not live on a track so i should be able to improve on both areas.

with regards to the acceleration times i'm as interested as you, will be nice to see how consistent the car is and also measure any difference in D, S & LC mode.

i'm sure there is a thread here that has people P3 or 0 to 100 times in it but i can only find track time thread, have you any idea where it might be?

I'll be at the DIY mate so we can catch up there, or you could move to Manly

Pay for my rent? >D

When I eventually get BBKs way way later on down the track, aesthetics will be involved for sure. My car will never see the track so may as well go the hardparker route ;)

Heres the link to the P3 0-100 thread

http://www.vwgolf.net.au/showthread.php?6167-P3-0-100-TIMES

Have some questions I gotta ask you as well when we meet

[BBR32]

any more on this ?????

[CSR]

Did you get that O2 sensor resolved buddy?

[Adamolee]

http://img254.imageshack.us/img254/6610/sam1214n.jpg

http://img860.imageshack.us/img860/9189/sam1212.jpg

http://img708.imageshack.us/img708/481/sam1210l.jpg

http://img9.imageshack.us/img9/7985/sam1209y.jpg

[Jig]

Looks very classy rather than Evil Chief. Why the change?

[Adamolee]

Looks very classy rather than Evil Chief. Why the change?

Morning sir,


Had a pretty bad accident before christmas and with ADV's exceptional customer service, I am still waiting for the part to repair my damaged wheel (This is week 9)

As we were about to leave Sydney and move northwards I had no choice but to get the car back on the road, so I got my hands on some wheels as quick as I could or it would still be on a hoist in Sydney.

Not sure what I will do once the ADV is repaired, I love the wheels but have come to loath the company.

Not sure I belong in the "classy" set my good man, these wheels are mean up close, honest!

going stage 2 in a few weeks, pulley, injectors, remap etc ... should be fun :D

[schoona]

I like ^

[Adamolee]

I like ^

Cheers Mal,

also fitted P3 Guage, slight mod to 2nd fuel pump, Unibrace underbody & Whiteline Antilift Kit

P.S. i'm living just down the road from you now mate, we should hook up a central coast meet

:D

[stephen8512]

new wheels look the business sir! long time no talk

[Adamolee]

new wheels look the business sir! long time no talk

Thanks buddy,

hard to capture on camera, they are pretty chunky and agro looking, you'll see what i mean when we catch up next,

its been a crap time lately, 6 weeks off work, a lot of time sitting in bed, too many Doctors! ... feeling good after the move though (not living in Syd anymore) so now when i get sick i can large it in my pool!

[M4RK0]

Nice wheels Adam,

Hope you are ok after the accident, :)

Are you coming to the DIY day?,

When are you ADV1's coming back?

Cheers!!

[BBR32]

this needs black they look good but need black :)

[Adamolee]

Nice wheels Adam,

Hope you are ok after the accident, :)

Are you coming to the DIY day?,

When are you ADV1's coming back?

Cheers!!

I was fine mate but I busted a wheel, a hub / carrier and bearing, ADV / Hawthorn can still not confirm when my part will arrive, First they couldn’t find the code so I sent it to them, then they said it was on backorder, then shipped, then they forgot to ship it etc ... The amount of bullshit that comes from that company is staggering ...

Am hoping to be there mate, last time was a blast but I had to shoot off for work so hopefully catch you then



this needs black they look good but need black :)

You mean like my ADV's you narna?

http://img594.imageshack.us/img594/4052/dsc1682.jpg

[drewr]

Awesome Adam! Looking great mate!

Whens the 92mm pulley/440c injector upgrade coming?! Sounds like the other twin has trial and error'd for us now!

Loving the new wheels, but I think the all black look is stunning, executed so well.

[Adamolee]

Awesome Adam! Looking great mate!

Whens the 92mm pulley/440c injector upgrade coming?! Sounds like the other twin has trial and error'd for us now!

Loving the new wheels, but I think the all black look is stunning, executed so well.

Hello mate,

Am waiting on dates from RS now, I have requested 11 "items" so it may take a while to talk nonsense and such before I drop off the car, but i'd like to have it in their hands mid Feb

I did ask if we can skip a stage or two and just go bonkers so stay tuned on that, as for trial and error, I’m pretty sure Jig has opted to keep rocking stage 1, he did have headers, cats and OEM pulleys changed but as far as I know has not gone stage 2 on the SC, he may have had a custom tune, but he'll need to confirm that. The trial and error was related to the number of grooves on the main crank pulley, apparently Aus R32's have 5 and the part supplied had 4, so all pulleys were changed for billet units except main crank, again the boss man would need to confirm that himself.

I'll be back to black once ADV sorts themselves out and gets my parts here, but for now I’m loving the fake VMR's, they look at bit posh in pics bit are pretty agro up close .

How you liking your beast ?

any plans for more insanity?

[drewr]

Hello mate,

Am waiting on dates from RS now, I have requested 11 "items" so it may take a while to talk nonsense and such before I drop off the car, but i'd like to have it in their hands mid Feb

I did ask if we can skip a stage or two and just go bonkers so stay tuned on that, as for trial and error, I’m pretty sure Jig has opted to keep rocking stage 1, he did have headers, cats and OEM pulleys changed but as far as I know has not gone stage 2 on the SC, he may have had a custom tune, but he'll need to confirm that. The trial and error was related to the number of grooves on the main crank pulley, apparently Aus R32's have 5 and the part supplied had 4, so all pulleys were changed for billet units except main crank, again the boss man would need to confirm that himself.

I'll be back to black once ADV sorts themselves out and gets my parts here, but for now I’m loving the fake VMR's, they look at bit posh in pics bit are pretty agro up close .

How you liking your beast ?

any plans for more insanity?

From what Thomas says, Jiggys gone injectors, pulley, headers and cats! Going bonkers sounds good, i like it! 11 "items" oh man that's a tease!

Yeah that sounds about right from our discussions! Good to hear- murdeeeer it out again.

Yeah mate sure do! Should unfold in the next few months! Still tinkering with suspension setup for now though. Got a couple little bits and pieces to install too. Will post a thread soon enough.

[Jig]

I am with you as well. This is my last set of Wheels from them. Moving on to other sets for sure.

If you want to feel what stage2 is like, let me know. My car is now on stage 2 with the 92mm pulley compared to the 88mm pulley with the bigger injectors and the custom tune for stage2. While I was at it, Ramspeed also did the dsg tune on my car and it's a different car altogether. The best thing about stage 2 is the SC whine is 10x louder and with my bonnet vents you can hear it from a mile away. It also made my capristo sound like an AMG burble. It's not as raspy as before. Loving it.

Once your done with stage 2, some tunnel drives are in order. All the best chief.


Morning sir,


Had a pretty bad accident before christmas and with ADV's exceptional customer service, I am still waiting for the part to repair my damaged wheel (This is week 9)

As we were about to leave Sydney and move northwards I had no choice but to get the car back on the road, so I got my hands on some wheels as quick as I could or it would still be on a hoist in Sydney.

Not sure what I will do once the ADV is repaired, I love the wheels but have come to loath the company.

Not sure I belong in the "classy" set my good man, these wheels are mean up close, honest!

going stage 2 in a few weeks, pulley, injectors, remap etc ... should be fun :D

[Jig]

Hey Drew, the invitation is extended to you too mate which goes without saying. Us triplets need to be tight.

I hope you are on the mend Adam. Health is king. I had a stupid accident yesterday and stuffed my lower right rib. Things like wiping your bottom is a process in itself. Stuck at home recuperating and in bed as we speak. Not fun. Look after your selves.

[drewr]

Certainly- looking at coming down to Syd around easter with the R32 Jig- so may be able to shed some light then! Judging from emails, stage 2 power seems low :S

[stephen8512]

so you keeping it drew?

[Adamolee]

Got bored,

Did this

http://img690.imageshack.us/img690/9516/48306872.jpg

http://img407.imageshack.us/img407/3473/99265185.jpg

http://img827.imageshack.us/img827/3711/47786540.jpg

http://img215.imageshack.us/img215/2986/98767950.jpg

[Stalker]

Nice. :)

[just_quietly]

wrong colour.....I need them red adz..... :)

[Adamolee]

wrong colour.....I need them red adz..... :)

Happy to do them for you again boss,

much easier when they're off the car

>D

[just_quietly]

Haha. It's all good.

[Footguy]

How well does painting them this way hold up? Mine are barely red after my last track session...

[Adamolee]

How well does painting them this way hold up? Mine are barely red after my last track session...

Hey Tom,


I cant say yet, but i have my concerns,

when still attached it is not possible to fully clean and remove all dust and crap so prep work is not 100%

the paint itself is epoxy rated to 900F but again the only thing that will prove that claim is time,

I wanted to give it a go anyway and the bang for buck and ease is well worth it, as it only cost me $60.00 for a wire brush some break cleaner and the paint.

i am planning on fitting new brakes shortly so if it all turns out crap after my first quick run all is not lost, i'll just rip them off and sell em to Jas

:D

[M4RK0]

wrong colour.....I need them red adz..... :)

Maybe in Orange!! :)

Looks good Adam!

When you get bored again can you do stuff in my car??? LOL!

[Adamolee]

Maybe in Orange!! :)

Looks good Adam!

When you get bored again can you do stuff in my car??? LOL!


Marco as nice as it sounds to have a car butler you do not want me loose near your car with tools and paint!

I trip over flat concrete!

>D


p.s i will do anything "in" your car you like, no cameras!

[Footguy]

Cool. Thanks. Will wait with interest....

Agreed though, just need new brakes....!

[Adamolee]

Just got an email from RUF Automobile GmbH,

That's all, for now

[Jig]

Just got an email from RUF Automobile GmbH,

That's all, for now

This is going to be good. Nothing but love for RUF.

[fuzion]

This is going to be good. Nothing but love for RUF.

Their workshop is tiny. I had organised a walk through with them about 2 years ago and they were quite happy to do so but was so far out of the way. M5 Ring Taxi took place fortunately enough though.. 2 bookings on one day why would i say no lol.

Saw 2 RUF 911's last time in October though, cream pants material. Oh and a mansory panamera, that was nice in an expensive bad taste way lol

[Seby123]

Their workshop is tiny. I had organised a walk through with them about 2 years ago and they were quite happy to do so but was so far out of the way. M5 Ring Taxi took place fortunately enough though.. 2 bookings on one day why would i say no lol.

Saw 2 RUF 911's last time in October though, cream pants material. Oh and a mansory panamera, that was nice in an expensive bad taste way lol

Mansory cars normally look over the top but i actually like their Panamera. even though i hate the Panamera stock lol. i saw the mansory version at the frankfurt motorshow!

Cant believe ive never seen this R32 though haha MEAN!

[Adamolee]

Just wanted to add this in as I was chatting about it today to a few folks

Recently I lost fuel pressure while driving, after about 30 secs I smelled fuel and by that time had come to rest in a side street, as ignition was still in the 'on' position my 2nd fuel pump was still dumping fuel all over the road, I shut the car off and jumped underneath to find the low pressure side of the pump had lost its hose, the culprit was a single use clamp.

I shoved on a $1.00 clamp from Bunnings but it will rust as only the band is stainless and not the screw, you can get full stainless clamps from marine shops if you have rusty clamps.

The replacement I have ordered is also full stainless but has no thread in the band nor is there any pinch point or potential for it to split your hose (I’m pedantic)

Her is a Pic of the offending clamp (left) and the temp replacement (right)

http://img213.imageshack.us/img213/6840/sam1260t.jpg

And link to the type of insane perfectionist clamp should anyone need to change any clamps in future

http://www.tboltclamps.net/img/t-bolt-clamps-image.jpg

http://www.ebay.com.au/itm/250862614510?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649

[fuzion]

Mansory cars normally look over the top but i actually like their Panamera. even though i hate the Panamera stock lol. i saw the mansory version at the frankfurt motorshow!

Cant believe ive never seen this R32 though haha MEAN!

not hijacking thread but incase people are going wtf

https://fbcdn-photos-a.akamaihd.net/hphotos-ak-ash4/305330_10150842536600243_756085242_20954230_178895 6207_a.jpg in Zurich

[Adamolee]

not hijacking thread but incase people are going wtf

https://fbcdn-photos-a.akamaihd.net/hphotos-ak-ash4/305330_10150842536600243_756085242_20954230_178895 6207_a.jpg in Zurich

Am glad i don't live in Dubai, otherwise i'd have to like that thing

grim!

;)

Would rather talk about Porsche than hose clamps anyday matey

[fuzion]

The clamps mentioned are really good. But be careful you don't over tighten them as they can cause damage to hoses if they dont have rolled edges.. my friend could speak from experience LOL

[Adamolee]

Got some of these for the front,

http://www.goingsuperfast.com/images/996_GT-2_yellow-3.JPG

http://img201.imageshack.us/img201/4053/sam1371.jpg

Some of these for the back

http://img689.imageshack.us/img689/5522/backad.jpg

a little bit of this for everywhere else

http://img651.imageshack.us/img651/6858/volkswagengolf5gearknob.jpg

http://img10.imageshack.us/img10/2712/volkswagengolf5100.jpg

And possibly some of these

http://img840.imageshack.us/img840/8774/twsxq.jpg

or these

http://img856.imageshack.us/img856/7961/mht.jpg

But may end up here instead

http://img233.imageshack.us/img233/514/rsdc09satinmattblackcen.jpg

[adrian13]

Oh my gosh! I feel more excited for this build than girls meeting one direction for the first time! (my sister and girlfriend loves them :P) great stuff adam!

[just_quietly]

Ah yeah baby. Everything looking smik adz. Yellow caliper with the black will look great. Any reason for drilled at the front and slottered for the rear?
Carbon will work so well too. Nicely coming together mate.
Re the wheels, the last two choices have my vote.

[Adamolee]

Oh my gosh! I feel more excited for this build than girls meeting one direction for the first time! (my sister and girlfriend loves them :P) great stuff adam!

Thanks Adrian, p.s Mrs Adrian needs to sort her musical preferences out


Ah yeah baby. Everything looking smik adz. Yellow caliper with the black will look great. Any reason for drilled at the front and slottered for the rear?
Carbon will work so well too. Nicely coming together mate.
Re the wheels, the last two choices have my vote.

Cheers matey,

Going to play with both and see what works out, when I saw Ray was selling his rear discs i decided to buy them and do everything at once, Didnt make sense to go BBK up front and do nothing up the back, so am keeping stock calliper but going slotted + braided that way i'll get everything done in 1 go,

might drive me nuts yet, what with the OCD n all,

we'll see,

[markwid]

WOW Adam, all nice goodies! Yeah, excited on your behalf...

As for the wheels, I like the ramspeed special (last pic - they really should name them to prevent bloody confusion), I like it a lot.

[Adamolee]

Thanks Mark,

As for the TWS option i think the price is restrictive, and they dont offer the flexability that Ramspeed do, MHT / Niche are very big in the US bit not so much out here so I dont have the confidence to go with an untrusted brand as they can't be vouched for, I love the design but again ... Ramspeed ....

The wheels are all named, This style is RS DC 09, i'm sure they will publish it all in good time,

[Jig]

Stepping it up Adam. Stepping it up.

[MalcolmlieuGTI]

Nice work Adam! Someone has been busy!
Keep it up :D

[Adamolee]

Forgot to mention these bad boys, S2T DSG paddles

The guys and the product are amazing,

http://img585.imageshack.us/img585/919/sam1348s.jpg

[stephen8512]

Like a sir!

Interior will be a nice place to be after these have been installed mate! looking sharp as always! Well done!

Really liking that CF DSG gearknob and the CF door handles. May I ask where you got them done from?

[Adamolee]

Ramspeed can turn anything into Carbon, inserts, plastic, mouldings etc, if you can hand it to them they will return it + Carbon, check this out

http://www.vwgolf.net.au/showthread.php?9624-To-all-the-Carbon-Fibre-Gurus-out-there!!!-I-need-your-help!!!

[stephen8512]

ahh cheers!

It looks awesome either way mate! Cant wait till you get your new shoes and get those brakes on!

[Rezz]

http://img840.imageshack.us/img840/8774/twsxq.jpg


http://img856.imageshack.us/img856/7961/mht.jpg


http://img233.imageshack.us/img233/514/rsdc09satinmattblackcen.jpg


My gawd i love the twin 5 spoke design.

Makes me gain an extra spoke if you know what i mean hahahahahah

[Adamolee]

Yeh man i hear ya

BOING!

http://img26.imageshack.us/img26/5973/boingh.jpg

[Dub]

Adam,

This thread is becoming disgracefully good. :)
Thomas tried to tempt me with carbon goodies. I was looking at the steering wheel and DSG stick, but looks like you are going to beat me to it :p

And by the way, damn nice choice on the brakes, and the wheels. Im getting wheel envy, and wondering if I picked the right ones now :)

So what happened to the awesomeness of brakes? Movit? :)


http://www.youtube.com/watch?v=yRoWs-L4vaI&feature=related

[Adamolee]

re: moveit = $17'000

So many R32 purchases and build threads kicking off i had to join in,

also you may still beat me to it on the carbon if you decide to do it, before I get any carbon fitted I need to

Paint and fit calipers front and rear
paint Brembo discs (they are grey and I want BLACK!)
Change my belts and pulleys
sort my guards out as they need to be rolled before I fit the new wheels as am going 35 ET
get my paint corrected and tidy up all the swirls and holograms
get the car to Heasmans for some camber and LCA's etc

Then I will have time to get it back to Ramspeed for the carbon treatment, so looks like I might be following in your footsteps, make with the carbon, GO, GO

MOVE IT !!!!

[MalcolmlieuGTI]

Adam,

This thread is becoming addicting :p (I couldn't agree more with Paul)
It look's like you just can't stop! this could be the most extensively modified R32 MKV in Australia :)
By the way mate, nice choice on the brake kit. Those wheels are 'special'. Im getting car envy, and wondering if I should by an R32. So what exactly did you end up going with for the brakes?

You my man, need to come to more meets to blow the socks off every one :D

[Adamolee]

Brakes are Porsche 996TT / GT3 6 piston up front with Brembo 350mm drilled discs off an AMG/Merc with braided lines and custom brackets supplied by LOBA with lots of help from Pierre (Fuzion) Rear is stock calliper painted in Porsche yellow with braided lines EBC redstuff pads and Neuspeed slotted 310mm discs supplied by Crazyray

I wish i could fully unleash all my ideas on this car but i have a lot going on and i dont have the time or funds to fully devote to it so it comes in waves,

Also got a custom Alcantarra wheel lined up and some fancy engine tuning but that will be the last thing on my busy little list, right after teh brakes, body, guards, carbon etc ...

Plenty of meets coming up in the next few weeks and months, i'm going to do my best to attent do might catch you there

[Dub]

ET 35? you extreme mofo.....jealous ! :)

[DBP]

And by the way, damn nice choice on the brakes, and the wheels. Im getting wheel envy, and wondering if I picked the right ones now :)

]

Wheel envy? What about BRAKE ENVY!!????

Adam, this car just keeps on getting better - attention to detail and quality yet wisely chosen components make this thread a joy to read.

[MalcolmlieuGTI]

Like a boss! >D

[Dub]

This thread...

http://i50.tinypic.com/2rom0zk.jpg

[Adamolee]

Pics Awesome homeboy

[sxcR32]

Thread of awesomeness!!!!

[Adamolee]

Forgot these,

not that they will ever be seen but they are beautiful and essential

Lovely billet brackets for my callipers

http://img440.imageshack.us/img440/9081/sam1373.jpg

[Dub]

sorted :)

Here's a thought Adam...

Given you turfed the back seat, and are setting bench marks, why dont you strip that dash down, rework the firewall, and get that engine sitting behind the front axle :)

Epic centre of gravity !

Just a thought :p

[Adamolee]

Next project will be powered by one of these - Nelson Racing (http://www.nelsonracingengines.com/)

http://img707.imageshack.us/img707/5184/injcdd.jpg


http://www.youtube.com/watch?v=O_863XEcHCM&feature=fvwrel

[CSR]

Oh my god..Drool...Adam you are one crazy son of a bitch, I can't wait to hear about your plans for this thing.

[M4RK0]

Awwww shit!! You've been busy bud!!!

Can't wait for those mods!!
Brakes in particular :) I have a gap to fill!

:)